DOCUMENT:Q87135 30-JUL-2001 [lanman] TITLE :Large Drive Translation Under Microsoft OS/2 1.3 PRODUCT :Microsoft LAN Manager PROD/VER: OPER/SYS: KEYWORDS: ====================================================================== SUMMARY ======= This article discusses large drive support for Microsoft OS/2 version 1.3. MORE INFORMATION ================ 1. Q. What is a large drive? A. A large drive is any disk drive with more than 1024 cylinders, 256 heads, or 63 sectors per track. "Large" does not refer to the capacity of the drive, but rather these parameters. The combination of cylinders, heads, and sectors per track is referred to as the actual geometry of the disk. These particular capacities were chosen to offer compatibility with IBM ROM BIOS and MS-DOS. Because OS/2 machines can be dual booted, or booted from an MS-DOS floppy disk, it is necessary to maintain the same use of partition tables as that employed by MS-DOS. Because these limits exist in MS-DOS, they are inherited in OS/2. 2. Q. Why does this affect booting OS/2? A. OS/2 employs the ROM BIOS during boot. Until the OS/2 kernel, loader, and disk drivers have loaded, OS/2 must go through the ROM BIOS. After these have loaded, OS/2 goes into protect mode disk operation, eliminating the need to interface with the ROM BIOS. However, as the kernel, loader, and disk drivers are loaded, it is imperative that these files lie within the boundaries the ROM BIOS can access. If any of them lies outside these boundaries, that file cannot be accessed as OS/2 boots, and therefore the system will hang. 3. Q. How is disk capacity computed? A. Disk drive capacity is computed by the following formula: cylinders * heads * sectors per track * sector size = disk capacity The IBM ROM BIOS standard dictates that the cylinder addressing is limited to 10 bits (maximum of 1024), head addressing to 8 bits (maximum of 256), and sector addressing to 6 bits (maximum of 63, because sector addressing is 1-based). OS/2 uses a sector size of 512 bytes. 4. Q. What can we do with drives that exceed the maximum geometry? A. Two choices are available when a drive exceeds any of the above parameters: truncation or translation. If the truncation method is chosen, the offending parameter will simply be truncated to the maximum allowable for that field. For example, suppose the drive in question has 1740 cylinders (c), 14 heads (h), and 54 sectors per track (spt). If truncation were employed, OS/2 would use an apparent geometry of 1024 cylinders, 14 heads, and 54 sectors per track. The other 716 cylinders would be lost. In this case, the truncated drive would lose about 41 percent of the available drive space. If translation were used, no drive space would be lost. Translation requires decreasing the offending parameter until it is within acceptable bounds, and increasing another parameter a corresponding amount. Using the above example, the drive could be translated to have 870 cylinders, 28 heads, and 54 sectors per track. In this way, no drive space is lost. 5. Q. Which method does Microsoft OS/2 version 1.3 employ? A. Microsoft OS/2 1.3 employs both methods under different circumstances. In the case of a boot drive, truncation is used. This is because of the limitations stated above (the OS/2 kernel, loader, and disk driver can be located on a disk partition that is accessible by the ROM BIOS). If translation were done, one or more of these files could reside on a disk location outside of the addressable geometry, resulting in an unbootable system. Therefore, for boot drives, disk truncation is used. This may result in some available drive space being lost; however, it does ensure that the machine will be bootable. For non-boot drives, however, translation is employed. This can be done safely because the operating system is already loaded. Therefore, translation can be done safely and no disk space should be lost. How Translation Is Done ----------------------- Translation can be done in one of several ways: via hardware, hardware with software support, or software only. For hardware incapable of doing translation at a hardware level, MS OS/2 1.3 supports software translation. Because all disk activity goes through the disk drivers as provided by the LADDR architecture, translation can be done at this level. For hardware with software support translation, the bus interface driver (BID) is responsible. For software-only support, the DISK.TSD (type specific driver) does all of the work. The DISK.TSD does the translation in the following manner: If there are more than 1024 cylinders, and if this is the boot drive, set the apparent geometry to have 1024 cylinders, and the actual number of heads and sectors per track. If it is not the boot drive, halve the number of cylinders, and double either the heads, or sectors per track. Repeat the last step until the number of cylinders is less than 1024, or until the heads and sectors per track no longer can be doubled. Sectors per track are increased before the number of heads. For example, a Seagate ST 4769E (691 MB ESDI drive) will generate the following translation table: Actual Physical Translation If Translation If Drive Parameters Boot Drive Not Boot Drive ---------------- -------------- --------------- 1552 cylinders 1024 cylinders 776 cylinders 15 heads 15 heads 30 heads 53 sectors per track 53 sectors per track 53 sectors per track To determine which method has been employed, use the LOGSHOW.EXE utility, which is shipped with MS OS/2 1.3. This utility reports what the operating system determines your actual and apparent geometry to be. If you are Running LOGSHOW from an OS/2 command prompt, press F1 to examine the existing log files, and then select the latest log file from the list. A screen showing a variety of information will be displayed. The area of interest is the DISK01 header, approximately midpoint of the screen. For example: DISK01 ffff 04/10/92 14:12:47 - Informational: configure physical disk AOK Apparent geometry: 00512 000391200 000815 0015 0032 3700 Actual geometry: 00000 000000000 000815 0015 0032 65535 The fields are the same for the both the Actual and Apparent geometry, with the exception of the last field in each. The fields are as follows (from left to right): - Sector size (in BYTES) - Number of sectors on disk - Number of cylinders on the disk - Number of heads on the disk - Number of sectors per track - For the apparent geometry record, the last field is a set of flags that detail how the geometry was determined. - For the actual geometry record, the last field is the write precompensation cylinder Using this information, it is easy to see what, if any, translation or truncation has been performed on the disk drive. Known Problems with MS OS/2 1.3 Drive Translation ------------------------------------------------- There are two problems with disk translation and the released version of MS OS/2 1.3. These problems deal with doing the translation incorrectly, and affect the following files: DISK.TSD ESDI-506.BID The ESDI-506.BID is needed for any ESDI/IDE/ST-506 (MFM, RLL) drives for which translation is required, while DISK.TSD is required for all drives doing translation. These corrections are available from Microsoft Product Support Services. Note that these corrections only affect systems doing translation. Additional query words: 2.10 1.30 disk.tsd esdi.bid translate hard disk drive ====================================================================== Keywords : ============================================================================= THE INFORMATION PROVIDED IN THE MICROSOFT KNOWLEDGE BASE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. MICROSOFT DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SO THE FOREGOING LIMITATION MAY NOT APPLY. Copyright Microsoft Corporation 2001.