DOCUMENT:Q149449 20-MAY-2002 [win95x] TITLE :IR Communications Driver 2.0 Relnotes.doc (Part 1 of 2) PRODUCT :Microsoft Windows 95.x Retail Product PROD/VER:Win2000:95 OPER/SYS: KEYWORDS:win95 ====================================================================== ------------------------------------------------------------------------------- The information in this article applies to: - Microsoft Windows 95 ------------------------------------------------------------------------------- SUMMARY ======= This information is a copy of the information in the Relnotes.doc file included with the Microsoft Windows 95 Infrared Communications Driver version 2.0. MORE INFORMATION ================ Microsoft Windows 95 Infrared Communications Driver Version 2.0 Release Notes 10 May 1996 Copyright Microsoft Corporation 1996. All Rights Reserved. Contents Infrared Communications Driver, Version 2.0 Using the IR Communications Driver Troubleshooting Product Support INFRARED COMMUNICATIONS DRIVER, VERSION 2.0 =========================================== The Infrared Communications Driver, Version 2.0, is an optional component of the Windows 95 operating system. The Infrared Communications Driver supports hardware devices which enable networking and communications over the infrared media. The hardware device can be either an infrared port built into the platform or an infrared adapter connected to one of the platform's serial or parallel ports. User motivations for installing the infrared hardware device and the Version 2.0 Infrared communications driver are: - The user can use wireless IR links instead of serial and parallel cables. For example, files can be exchanged wirelessly between two computers that have an IR device and the Version 2.0 driver installed, instead of using a serial or parallel cable. Files can also be printed wirelessly on IR-capable printers. - The user can use wireless IR links instead of LAN cabling, if the user has an IR-capable LAN access point product connected to the network (see "Using the IR Communications Driver" for a list of LAN access point products the Version 2.0 IR driver has been tested with). The Version 2.0 IR communications driver supports IR communications links running at speeds up to 115.2 kbps. USING THE IR COMMUNICATIONS DRIVER ================================== This section of the Release Notes lists the hardware and software components on which the Version 2.0 IR communications driver has been tested. Notebook Computers ------------------ The Version 2.0 IR communications driver has been successfully tested on the following Windows 95 notebook computers that have built-in IR ports: Gateway 2000 Liberty HP Omnibook 600CT HP Omnibook 4000C IBM ThinkPad 701C (Butterfly) Sharp PC 3050 TI TravelMate5000 Some testing of the Version 2.0 IR driver was also done on these Windows 95 notebooks: Digital HiNote Ultra CT475 TI TravelMate 5000 IR Adapters ----------- The Version 2.0 IR driver has been successfully tested on Windows 95 platforms with the following IR adapters connected to serial ports: ACTiSYS ACT-200L Infrared Wireless Interface ACTiSYS ACT-220L Infrared Wireless Interface Adaptec AIRport APA-9320 External Infrared Adapter (this adapter is also called the Adaptec AIRport 2000) AMP PhasIR Serial Adapter Extended Systems JetEye PC Infrared PC Interface (ESI-9680) Parallax IR Adapter LiteLink PRA9500A To obtain any of the IR adapters listed above, contact the adapter manufacturer. The addresses of these manufacturers are listed in "IR Adapter Manufacturer Names and Addresses" at the end of this document. Applications ------------ The following applications have been run successfully over an IR communications link, using the IR communications driver and the hardware listed above: Windows 95 Direct Cable Connection (DCC). Various Windows communications applications, including HyperTerminal and DynaComm. Because the IR link simulates a serial communications link, some communications applications may not perform as expected after they connect over the IR link. See "Troubleshooting" for more information. For instructions on running DCC over an IR link, see "Notes on Running the Direct Cable Connection Application Over an IR Link" later in this document. Printers -------- Numerous Windows 95 applications have successfully printed over an IR link to an HP Laserjet 5P or 5MP printer, which have built-in IR ports. Numerous Windows 95 applications have also printed successfully over an IR link to other printers with an Extended Systems JetEye Infrared Printer Port ESI- 9580 infrared adapter connected to the printer parallel port. IrLan Access Points ------------------- Local area network access over an IR link has been tested with the following IrLan access point devices: Extended Systems ESI-9910 JetEye Net Plus. Hewlett-Packard NetBeam IR Infrared LAN Adapter. TROUBLESHOOTING =============== Some general troubleshooting tips are: - A user must always remove any previously installed version of the IR communications driver every time the driver is installed. If Version 1.0 of the driver is installed, it must be removed before installing Version 2.0. If an early Beta release of the Version 2.0 driver is installed, it must be removed before installing the current Version 2.0 release. Instructions for removing the IR communications driver are in "An Optional Step: Removing the IR Communications Driver." - If the user changes the IR adapter model that is connected to the computer, the user must remove the installed IR communications driver and reinstall it, specifying the new IR adapter type. Instructions for removing the IR communications driver are in "An Optional Step: Removing the IR Communications Driver." - During installation of the IR communications driver, a user may select the wrong port when the Add Infrared Device Wizard prompts for the physical COM port to which the IR device is connected. If the user selects the wrong COM port, the IR device will be unable to discover another IR device within range. Reasons why the user may select the wrong COM port vary, ranging from reasoning such as "there is only one physical COM port for the IR adapter to be connected to so it must be COM1" to mislabeled COM ports on the computer case to the simple fact that the user doesn't know which COM port to select and doesn't know how to find out. A troubleshooting procedure is: 1. Put an actively searching IR device close to the computer's IR device. 2. Click the Infrared Monitor Options tab and then choose a different communications port (for example, COM1 instead of COM2). 3. Continue selecting different COM ports in this way until the IR device on the computer discovers the nearby IR device. Note that the alternatives displayed in the IrMon Options tab are always based on the internal wiring of the computer platform: - COM1 always means a COM port wired to IRQ 4 and I/O address range 0x3F8 to 0x3FF. - COM2 always means wired to IRQ 3 and 0x2F8 to 0x2FF. - Physical COM3 always means IRQ 4 and 0x3E8 and 0x3EF. - Physical COM4 always means IRQ5 and 0x2E8 and 0x2EF. - To get two IR devices to discover each other, the user may have to realign the IR devices so they point right at each other, move them closer together, and/or change the batteries in an IR adapter or plug the AC power into an IR adapter. The devices must be three feet apart, or less, and the angle of the cone of IR transmission is 30 degrees. Some devices work best if kept at least six inches apart. - If an IR adapter is attached to a COM port that is using an 8250 UART instead of a 16550 UART, or if an IR adapter is connected to a relatively slow computer (such as a 386 running at 20 MHz), the user might need to use the Limit Connection Speed To option in the Infrared Monitor Options tab to limit the connection speed to 19.2 kbps. After establishing a successful IR connection at this speed, the user can use the Limit Connection Speed To option to experiment with establishing a connection at a higher speed on their particular computer. - If the IR Monitor Options tab is used to change the port the IR adapter is attached to while IR communications are in progress, the IR connection is lost without prompting the user to verify that it is OK to disconnect. - Communication over a virtual COM port link between two computers may not be reliable if a printer's IR adapter is also within range. The user should move the printer's IR adapter out of range. - A user should not suspend a Windows 95 computer while an IR connection is established. Wait until the IR link is disconnected or force a disconnection before putting the computer in suspend mode. For example, if an IrLan connection is established on a laptop, the user must always move the laptop out of range of the IrLan access point before suspending the system or closing the laptop lid. Otherwise, the connection remains active and over time can drain the battery. - Connecting and disconnecting over a low-speed IR link or over a poor- quality link can take a long period of time (a few seconds), during which time the screen will appear to be frozen. To work around this, the user should use a higher-speed connection and/or take steps to improve the quality of the connection by, for example, realigning the IR devices so they point right at each other, moving the devices closer together, changing the batteries in an IR adapter, or plugging the AC power into an IR adapter. Troubleshooting Tips Specific to Using IrLan Access Point Devices Are --------------------------------------------------------------------- - Do not assume that because an IR device on a PC communicates with an IR device on another PC at 115.2 kbps that the IR device will also communicate with an IrLan access point device at that speed. For example, suppose a user has two PC-based IR devices that have negotiated a link speed of 115.2 kbps. Then if the user points one of the devices at an IrLan access point device, these two devices can negotiate a link speed of 115.2 kbps but no subsequent communication takes place (the PC has no access to the network through the IR link). No error message is displayed in this case. - Extended Systems ESI-9910 JetEye Net Plus users utilizing NETBEUI may receive an error message when copying large files (for example, 5 MB files) to a network drive. If this happens, call Extended Systems, Inc. product support for NETBEUI configuration changes. For Extended Systems, Inc. contact information, see the topic "IR Adapter Manufacturer Names and Addresses." - If there is a problem establishing an IR link to an IrLan access point device when the network is also connected to a network interface card in the computer, try disconnecting the LAN from the network interface card. Restart the computer and make sure the computer IR device and the LAN access point IR port are within range. Then use the Infrared icon in the Control Panel to activate the IR link between the computer and the LAN access point device. - The IPX protocol may not communicate over an IrLan access point. This can be caused by the Dial-Up Adapter becoming the primary IPX adapter and no other adapter, such as the IrLan adapter, can take over. To get around this problem, the user can create a profile that does not contain the dial-up adapter and use it when accessing the net through IrLan. - During a file copy to a NetWare server running burst mode, if the IR connection between the computer and the IrLan access point is disconnected (for example, the IR beam is blocked), the file transfer cannot recover and the computer screen will stay the same indefinitely. If this happens often, turn off burst mode to enable recovery from a disconnection. There will be performance degradation with burst mode off. - Using the virtual parallel port connection to an Extended Systems ESI- 9910 JetEye Net Plus IrLan access point to send data to a printer may result in a program fault. To get around this, use the virtual serial port on the IrLan access point to reach the printer. Troubleshooting Tips Related to Using Particular Applications Over IR Links Are ----------------------------------------- - If the Windows 95 application HyperTerminal is used to transfer files, there may be trouble doing file transfers successfully over an IR link. If the Zmodem protocol fails with a link speed of 115.2 kbps, use the IR Monitor Limit Connection Speed To tab to limit the link speed to 19.2 kbps and then retry the Zmodem file transfer. - When the Windows 95 application Direct Cable Connection (DCC) is run to establish the connection between the host and guest computers, the guest computer may display the message "Direct Cable Connection was unable to display shared folders of the host computer" and prompt the user to enter the computer name of the host computer. A convenient way to find the computer name of the host computer is on the Status tab of the Infrared Monitor interface screen. - When the Windows 95 application Direct Cable Connection (DCC) is run to establish an IR connection between the host and guest computers, DCC prompts the user to select a communications port (this procedure is described in the topic "Establishing and Using the DCC IR Link Between Host and Guest"). Selecting the virtual Infrared port in this step will fail (DCC announces the virtual port is not available) in the rare case that the user has suspended the Windows 95 operating system before invoking DCC in a session. Restart Windows 95 to begin a new session and DCC will work over an IR link. A Troubleshooting Tip Related to Developing an IrDA Standard IrCOMM Component for an IR Communications Driver Is ------------------------------------------------------------ - The IrCOMM implementation in the IR communications driver that runs on Windows 95 supports full emulation of 9-wire connections, but does not support emulation of 3-wire cooked connections. A specific example of this is the inability to print over an IR virtual COM port from the MS- DOS prompt, which uses a 3-wire cooked connection. IrDA drivers developed for platforms designed to communicate with Windows 95 platforms over IR links must implement full emulation of 9-wire connections (as specified in the IrDA IrCOMM specification). For example, a pair of handheld computer platforms may communicate with each other over IR links using 3-wire cooked emulation. However, if the user also expects to use one of the handhelds to communicate with a Windows 95 computer then the handheld IR driver must implement 9-wire connections. Troubleshooting Tips Related to Specific Infrared Hardware Are -------------------------------------------------------------- - The Adaptec AIRport 2000 infrared adapter can be powered by either the serial port, installed AA batteries, or an external power supply. In some cases, the serial port may not provide sufficient power for the operation of the adapter. This can cause reduced operating range and/or a failure to find another IR device which is nearby and aligned correctly. If such a problem is suspected, connect an AC adapter or add four AA batteries to the battery compartment in the infrared adapter. This will assure sufficient power. In some instances, the user may need to separate the adapter by at least six inches from the other IR device. - If an ActiSys 220L IR adapter is attached to a computer and used to print to a printer that is using an Extended Systems ESI-9580 printer IR adapter, or for printing to an HP DeskJet 340, the Options tab in the Infrared Monitor must be used to limit the connection speed to 19.2 kbps to print successfully. If the IR devices are allowed to automatically negotiate the connection speed without setting this limit, they will negotiate a higher connection speed and an application will not be able to print. - The TI TravelMate 5000 may communicate over an IR link only at very low speeds (9600 bps). - The Sharp PC 3050 may communicate over an IR link only at speeds between 9600 bps and 19.2 kbps. - For the HP Omnibook 4000C or an HP Omnibook 600CT, which have built-in infrared ports, a special echo-canceling serial driver must be installed in addition to the components that make up the IR communications driver. The echo-canceling driver, along with instructions on how to install it, are available from Hewlett-Packard. For a complete list of Microsoft Product Support Services phone numbers and information on support costs, please go to the following address on the World Wide Web: http://support.microsoft.com/default.aspx?scid=fh;EN-US;CNTACTMS Additional query words: irda irda2 ir w95ir.exe ====================================================================== Keywords : win95 Technology : kbWin95search kbZNotKeyword3 Version : Win2000:95 ============================================================================= THE INFORMATION PROVIDED IN THE MICROSOFT KNOWLEDGE BASE IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND. MICROSOFT DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL MICROSOFT CORPORATION OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL, LOSS OF BUSINESS PROFITS OR SPECIAL DAMAGES, EVEN IF MICROSOFT CORPORATION OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SO THE FOREGOING LIMITATION MAY NOT APPLY. Copyright Microsoft Corporation 2002.