======================================================================
  Microsoft(R) Product Support Services Application Note (Text File)
 WA1058: MICROSOFT MAIL FOR WINDOWS(TM) MAILMGR.DLL VERSION 3.2.0.4074
======================================================================
                                                   Revision Date: 9/94
                                                       1 Disk Included

The following information applies to Microsoft Mail for PC Networks,
version 3.2.

-----------------------------------------------------------------------
| INFORMATION PROVIDED IN THIS DOCUMENT AND ANY SOFTWARE THAT MAY     |
| ACCOMPANY THIS DOCUMENT (collectively referred to as an Application |
| Note) IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER      |
| EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED      |
| WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR       |
| PURPOSE. The user assumes the entire risk as to the accuracy and    |
| the use of this Application Note. This Application Note may be      |
| copied and distributed subject to the following conditions:  1) All |
| text must be copied without modification and all pages must be      |
| included;  2) If software is included, all files on the disk(s)     |
| must be copied without modification (the MS-DOS(R)  utility         |
| diskcopy is appropriate for this purpose);  3) All components of    |
| this Application Note must be distributed together;  and  4) This   |
| Application Note may not be distributed for profit.                 |
|                                                                     |
| Copyright (C) 1994 Microsoft Corporation.  All Rights Reserved.     |
| Microsoft and MS-DOS are registered trademarks and Windows is a     |
| trademark of Microsoft Corporation.                                 |
|---------------------------------------------------------------------|

Introduction
------------

The disk provided with this Application Note contains MAILMGR.DLL, a
replacement for the MAILMGR.DLL file that is included with version 3.2
of Microsoft Mail for Windows. The replacement file provides
additional enhancements to the original MAILMGR.DLL file.

This replacement file resolves the following problem that can occur
when you use version 3.2 of Microsoft Mail for Windows:

 - The Check Names function fails to properly resolve partial friendly
   names and returns several selections when a unique resolution is
   possible. This behavior is most obvious when the GAL is selected as
   the default address list and the first and last name of the
   intended recipient begin with the same letter.

   NOTE: To resolve this problem, two .DLL files must be updated: the
   MAILMGR.DLL file (update included in this Application Note) and the
   MSSFS.DLL file (update included in Application Note WA0760).

To replace your MAILMGR.DLL file
--------------------------------

1. Insert the enclosed WA1058 disk in your floppy disk drive.

2. At the MS-DOS command prompt, type the following and press ENTER

      copy <drive>:\mailmgr.dll <destination>

   where <drive> is the floppy disk drive containing the WA1058 disk
   and <destination> is the drive and directory where your MAILMGR.DLL
   file currently resides. For example, if MAILMGR.DLL is located in
   the MAILEXE directory on drive C and the WA1058 disk is in drive A,
   type the following command:

      copy a:\mailmgr.dll c:\mailexe

   A message will be displayed stating: 1 file(s) copied. This
   indicates that your MAILMGR.DLL file has been successfully
   replaced.

3. At the MS-DOS command prompt, type the following and press ENTER

      copy <mailexe>\setup.inf <mailexe>\setupinf.old

   where <mailexe> is the complete path to the directory containing
   the Microsoft Mail for Windows SETUP.EXE program. For example, if
   SETUP.EXE is located in the MAILEXE directory on drive C, type the
   following command:

      copy c:\mailexe\setup.inf c:\mailexe\setupinf.old

   A message will be displayed stating: 1 file(s) copied. This
   indicates that your SETUP.INF file has been successfully copied.

4. Using any text editor, edit the SETUP.INF file. In the [MSMAIL]
   section, replace the following line

      1, mailmgr.dll,,,, 1993-03-09, !DECOMPRESS,, OLDER,
      !READONLY,,,,, SHARED, 51632,,,, 3.2.0.4027,

   with:

      1, mailmgr.dll,,,, 1994-07-21, !DECOMPRESS,, OLDER,
      !READONLY,,,,, SHARED, 51696,,,, 3.2.0.4074,

   Save the file and close the text editor.

   NOTE: For these changes to affect the entire network, each existing
   user must run Setup again.